#Version check for XTRA
#DISABLE = 0
#AUTO    = 1
#XTRA2   = 2
#XTRA3   = 3
XTRA_VERSION_CHECK=0
#ODM
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0

#NTP server
NTP_SERVER=time.izatcloud.net

#XTRA CA path
XTRA_CA_PATH=/usr/lib/ssl-1.1/certs

# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
#               4 - Debug, 5 - Verbose
# If DEBUG_LEVEL is commented, Android's logging levels will be used
#ifndef OPLUS_BUG_DEBUG
#LinHuaqiu@CONNECTIVITY.GPS.LOCATION.LOG.1065783, 2017/11/04, Add for gps log control
#DEBUG_LEVEL = 3
#else /* OPLUS_BUG_DEBUG */
DEBUG_LEVEL = 2
#endif /* OPLUS_BUG_DEBUG */

# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0

# supl version 1.0
SUPL_VER=0x10000

# Emergency SUPL, 1=enable, 0=disable
#SUPL_ES=1

#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0

#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will overwrite the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#SUPL_MODE=

# GPS Capabilities bit mask
# SCHEDULING = 0x01
# MSB = 0x02
# MSA = 0x04
# ON_DEMAND_TIME = 0x10
# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING
CAPABILITIES=0x17

# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000

################################
##### AGPS server settings #####
################################

# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234

# FOR MO SUPL SUPPORT, set the following
# MO_SUPL_HOST=supl.host.com or IP
# MO_SUPL_PORT=1234

# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234

# Bitmask of slots that are available
# for write/install to, where 1s indicate writable,
# and the default value is 0 where no slots
# are writable. For example, AGPS_CERT_WRITABLE_MASK
# of b1000001010 makes 3 slots available
# and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0

####################################
#  LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default)
# 1: Enable LPP_User_Plane on LTE
# 2: Enable LPP_Control_Plane
# 3: Enable both LPP_User_Plane and LPP_Control_Plane
LPP_PROFILE = 2

####################################
#Datum Type
####################################
# 0: WGS-84
# 1: PZ-90
DATUM_TYPE = 0

################################
# EXTRA SETTINGS
################################
# NMEA provider (1=Modem Processor, 0=Application Processor)
NMEA_PROVIDER=0

# Customized NMEA GGA fix quality that can be used to tell
# whether SENSOR contributed to the fix.
#
# When this configuration item is not enabled (set to any value that is not 1),
# GGA fix quality conforms to NMEA standard spec as below:
# PPP/DGNSS/SBAS correction fix w/ or w/o sensor: 2
# RTK fixed fix w/ or w/o sensor: 4
# RTK float fix w/ or w/o sensor: 5
# SPE fix w/ or w/o sensor: 1
# Sensor dead reckoning fix: 6
#
# When this configuration is enabled (set to 1), GGA fix quality
# will be output as below:
# PPP fix w/o sensor: 59,                  w/ sensor: 69
# DGNSS/SBAS correction fix w/o sensor: 2, w/ sensor: 62
# RTK fixed fix w/o sensor: 4,             w/ sensor: 64
# RTK float fix w/o sensor: 5,             w/ sensor: 65,
# SPE fix w/o sensor: 1,               and w/ sensor: 61
# Sensor dead reckoning fix: 6
#
# any value that is not 1 - disabled
# 1 - enabled
CUSTOM_NMEA_GGA_FIX_QUALITY_ENABLED = 0

################################
# NMEA Reporting Rate Config, valid only when NMEA_PROVIDER is set to "0"
################################
# NMEA Reporting Rate
# Set it to "1HZ" for 1Hz NMEA Reporting
# Set it to "NHZ" for NHz NMEA Reporting
#Default : NHZ (overridden by position update rate if set to lower rates)
NMEA_REPORT_RATE=NHZ

# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
SGLTE_TARGET=0

##################################################
# Select Positioning Protocol on A-GLONASS system
##################################################
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
A_GLONASS_POS_PROTOCOL_SELECT = 0

##################################################
# Select technology for LPPe Control Plane
##################################################
# 0x1: DBH for LPPe CP
# 0x2: WLAN AP Measurements for LPPe CP
# 0x4: SRN AP measurement for CP
# 0x8: Sensor Barometer Measurement LPPe CP
#LPPE_CP_TECHNOLOGY = 0

##################################################
# Select technology for LPPe User Plane
##################################################
# 0x1: DBH for LPPe UP
# 0x2: WLAN AP Measurements for LPPe UP
# 0x4: SRN AP measurement for UP
# 0x8: Sensor Barometer Measurement LPPe UP
#LPPE_UP_TECHNOLOGY = 0

##################################################
# AGPS_CONFIG_INJECT
##################################################
# enable/disable injection of AGPS configurations:
#     SUPL_VER
#     SUPL_HOST
#     SUPL_PORT
#     MO_SUPL_HOST
#     MO_SUPL_PORT
#     C2K_HOST
#     C2K_PORT
#     LPP_PROFILE
#     A_GLONASS_POS_PROTOCOL_SELECT
# 0: disable
# 1: enable
AGPS_CONFIG_INJECT = 1

##################################################
# GNSS settings for automotive use cases
# Configurations in following section are
# specific to automotive use cases, others
# please do not change, keep the default values
##################################################

# AP Coarse Timestamp Uncertainty
##################################################
# default : 10
# AP time stamp uncertainty, until GNSS receiver
# is able to acquire better timing information
AP_TIMESTAMP_UNCERTAINTY = 10

#####################################
# DR_SYNC Pulse Availability
#####################################
# 0 : DR_SYNC pulse not available (default)
# 1 : DR_SYNC pulse available
# This configuration enables the driver to make use
# of PPS events generated by DR_SYNC pulse
# Standard Linux PPS driver needs to be enabled
DR_SYNC_ENABLED = 0

#####################################
# PPS Device name
#####################################
PPS_DEVICENAME = /dev/pps0

#####################################
# Ignore PPS at Startup and after long outage
#####################################
IGNORE_PPS_PULSE_COUNT = 1

#####################################
# Long GNSS RF outage in seconds
#####################################
GNSS_OUTAGE_DURATION = 10

#####################################
# AP Clock Accuracy
#####################################
# Quality of APPS processor clock (in PPM).
# Value specified is used for calculation of
# APPS time stamp uncertainty
AP_CLOCK_PPM = 100

#####################################
# MAX ms difference to detect missing pulse
#####################################
# Specifies time threshold in ms to validate any missing PPS pulses
MISSING_PULSE_TIME_DELTA = 900

#####################################
# Propagation time uncertainty
#####################################
# This settings enables time uncertainty propagation
# logic incase of missing PPS pulse
PROPAGATION_TIME_UNCERTAINTY = 1

#######################################
#  APN / IP Type Configuration
#  APN and IP Type to use for setting
#  up WWAN call.
#  Use below values for IP Type:
#  v4 = 4
#  v6 = 6
#  v4v6 = 10
#######################################
# INTERNET_APN = abc.xyz
# INTERNET_IP_TYPE = 4
# SUPL_APN = abc.xyz
# SUPL_IP_TYPE = 4

#####################################
# Modem type
#####################################
# This setting configures modem type
# (external=0 or internal=1)
# comment out the next line to vote
# for the first modem in the list
MODEM_TYPE = 1

##################################################
# CONSTRAINED TIME UNCERTAINTY MODE
##################################################
# 0 : disabled (default)
# 1 : enabled
# This setting enables GPS engine to keep its time
# uncertainty below the specified constraint
#CONSTRAINED_TIME_UNCERTAINTY_ENABLED = 0

# If constrained time uncertainty mode is enabled,
# this setting specifies the time uncertainty
# threshold that gps engine need to maintain.
# In unit of milli-seconds.
# Default is 0.0 meaning that modem default value
# of time uncertainty threshold will be used.
#CONSTRAINED_TIME_UNCERTAINTY_THRESHOLD = 0.0

# If constrained time uncertainty mode is enabled,
# this setting specifies the power budget that
# gps engine is allowed to spend to maintain the time
# uncertainty.
# Default is 0 meaning that GPS engine is not constained
# by power budget and can spend as much power as needed.
# In unit of 0.1 milli watt second.
#CONSTRAINED_TIME_UNCERTAINTY_ENERGY_BUDGET = 0

##################################################
# POSITION ASSISTED CLOCK ESTIMATOR
##################################################
# 0 : disabled (default)
# 1 : enabled
# This setting enables GPS engine to estimate clock
# bias and drift when the signal from at least 1
# SV is available and the UE�s position is known by
# other position engines.
#POSITION_ASSISTED_CLOCK_ESTIMATOR_ENABLED = 0

#####################################
# proxyAppPackageName
#####################################
# This is a string that is sent to the framework
# in nfwNotifyCb callback
#ifndef OPLUS_BUG_STABILITY
#LiZhilong@CONNECTIVITY.GPS.LOCATION.OPCUSTOMIZED.2786815, 2020/01/10, Modify for nfw proxy app
#PROXY_APP_PACKAGE_NAME = com.google.android.carrierlocation
#else /* OPLUS_BUG_STABILITY */
PROXY_APP_PACKAGE_NAME = com.oplus.locationproxy
#endif /* OPLUS_BUG_STABILITY */

#####################################
# CP_MTLR_ES
#####################################
# CP MTLR ES, 1=enable, 0=disable
CP_MTLR_ES=0

##################################################
# GNSS_DEPLOYMENT
##################################################
# 0 : Enable QTI GNSS (default)
# 1 : Enable QCSR SS5
# This setting use to select between QTI GNSS
# and QCSR SS5 hardware receiver.
# By default QTI GNSS receiver is enabled.
# GNSS_DEPLOYMENT = 0

##################################################
## LOG BUFFER CONFIGURATION
##################################################
#LOG_BUFFER_ENABLED, 1=enable, 0=disable
#*_LEVEL_TIME_DEPTH, maximum time depth of level *
#in log buffer, unit is second
#*_LEVEL_MAX_CAPACITY, maximum numbers of level *
#log print sentences in log buffer
LOG_BUFFER_ENABLED = 0
E_LEVEL_TIME_DEPTH = 600
E_LEVEL_MAX_CAPACITY = 50
W_LEVEL_TIME_DEPTH = 500
W_LEVEL_MAX_CAPACITY = 100
I_LEVEL_TIME_DEPTH = 400
I_LEVEL_MAX_CAPACITY = 200
D_LEVEL_TIME_DEPTH = 30
D_LEVEL_MAX_CAPACITY = 300
V_LEVEL_TIME_DEPTH = 200
V_LEVEL_MAX_CAPACITY = 400

##################################################
# Allow buffer diag log packets when diag memory allocation
# fails during boot up time.
##################################################
BUFFER_DIAG_LOGGING = 1
